Top
Mon - Sat : 08:00 - 17:00
7171 yonge street Thornhill, Toronto, ON L3T 0C5

Repair wood fence in Toronto

Repair wood fence in Toronto

Now it is rare to find a wooden fence in a private home - it has been replaced by concrete and iron structures. But it is wood that can give coziness and warmth, create an atmosphere of comfort - wooden fences have always been and will always be a priority for connoisseurs of beauty and style. Fences of the considered kind are often used on country sites - it is convenient, inexpensive and approaches to the general style of country possessions. Unfortunately, the tree occasionally loses its attractive appearance, and the humidity provokes the appearance of fungus and mold, which spoils the quality of the fence. How do you repair wood fence in Toronto if you don't have the specific knowledge and experience you need?

Dismantling a wooden fence in Toronto

Before you start repair wood fence in Toronto, it must be removed. And even if only one section has been damaged, it is worth examining the entire fence and identifying possible areas for repair/replacement.

Please note: Removal of the wooden fence in Toronto is mandatory - if you try to carry out the necessary repairs in suspension, the required quality will not be achieved due to difficult access to the lower parts of the sections and supports.

The following tool will be required for disassembly work:

  • a nail gun;
  • lever;
  • hacksaw;
  • wrenches/screwdrivers - if there are appropriate connections;
  • rubber or wooden hammer - it will minimize the risk of damage to parts of the wooden fence.

SUPPORT WORK

It is mandatory to repair a wooden fence in Ontario by inspecting the posts (pillars) on which the entire structure is mounted. Ignoring this recommendation, it is impossible to achieve high quality repair work and soon you will have to either replace the fence, or once again carry out a complete repair.

METAL SUPPORTS

Even if the outer metal supports have not been changed, but you know for sure that their replacement was carried out a long time ago and the poles are not concreted in the ground, you will have to give them time. To work, you need to prepare the next tool:

  • a crowbar and a shovel;
  • a bulgarian or a metal hacksaw;
  • metal brush to remove rust;
  • brush with stiff bristles.

What is included in the concept of repairing metal supports:

  • Pillars are dug entirely out of the ground.
  • The entire surface of the poles is cleaned of dirt, rust and old paint.
  • The prepared surfaces are painted.
  • The underground part of the metal supports of the wooden fence must be treated with rubber-bitumen mastic, except for paint, which will prolong their service life and prevent the appearance of rust.

POLES MADE OF WOOD

Most often after digging out wooden supports, active rotting of their underground part is observed. In this case, it should be cut off and the remaining surface should be examined for rotten/mold and part of the support cleaned up. Ideally, the next stage should be the complete drying of the wooden support, but the stage can only be carried out if technically possible and time is available. You can resort to an accelerated treatment of the wooden pole: it is treated with a special antiseptic, then covered with bitumen and painted.

If after removing the rotten underground part of the wooden support became much shorter and stopped approaching the fence, you can increase it to the bottom of the board post. The board should only be treated with antiseptic, protective compounds and bitumen in advance. Some masters recommend wrapping the base with roofing felt: this is acceptable, but not the best option. Repair wood fence in Toronto - contact us for this service!

Some craftsmen process wooden supports with fire - charring them with a soldering lamp, thus protecting them from rotting. This process is quite time-consuming and requires certain skills, so it is advisable to use special fluids - it may be more expensive, but it is more reliable and faster in processing time.

Before you start working with wooden supports, prepare a tool:

  • a hacksaw or chain saw;
  • a sharp knife;
  • hammer;
  • paintbrush for painting work.

CEMENT PIPES

They are often used to install wooden fences in Toronto, despite the fact that asbestos cement is the least practical material compared to wood and metal. If any damage is found on asbestos cement pipe supports, it is better to replace them immediately - repairs are not advisable. When installing the material in question as a support for a wooden fence, you should immediately equip them with top plugs - this will prevent water entry.

VENEER REPAIR

Before starting to repair fence sections, check the condition of the vents (bars). This is the second most important support element, which must be strong and reliable. Their task is to transmit the load to the fence poles.

Wooden beams (less often metal) are most commonly used as horizontal conductors. Wooden strands are not very strong, they can break or "fly away" together with the sections attached to them in case of strong wind gusts.

To connect damaged wooden bars, a section of thin-walled metal pipe can be used as a coupling.